The Motobilt Jeep JK Front The Hammer Bumper is a 48.5 inch wide, sleek, tight-fitting design proudly made in the USA. Our JK The Hammer Bumper is 3D CAD designed to ensure the best possible fit to your Jeep JK. The bumper will fit all year models of the Jeep JK 2 door and 4 door JK Unlimited. The front d-ring mounts are CNC cut from 3/4 inch thick steel plate and pass through the bumper where they weld to the bumper mounting plates in addition to the bumper body. This was done for added strength to the recovery point.
The Hammer bumper has provisions to mount the factory fog lights or aftermarket LED fog lights. We have pre-installed riv nuts for 10-24 screws in the factory bolt pattern. The Hammer bumper can be run with or without the optional skid plate. To install the skid plate, you have to trim approx 1 inch off each side of the crash bars. If you remove the skid plate later, the part that you trimmed will not be seen. The ends of the Hammer bumper taper up for tire clearance. Each cut in the bumper was intentional to keep it tight to the frame rail for a better approach angle. The main construction of the bumper is fabricated from 3/16 inch thick high strength steel plate. The bumper also serves as a winch mount. The top side of the JK The Hammer Bumper has bolt holes for a recovery winch.
Features:
Jeep JK The Hammer 48.5 inch front bumper with stinger and grill hoop
Fits all year models of the Jeep JK 2 door and 4 door JK Unlimited
Fabricated from 3/16 inch thick high strength steel plate
Bolt on design
3/4 inch thick steel d-ring mounts
Pass through d-ring mounts weld to the bumper
Pre-installed riv nuts for 10-24 screws in the factory bolt pattern
Made in the USA
Sold as each
Note:
If installing a winch, MB1002 fairlead mount will also need to purchased
Motobilt bumpers ship bare steel, paint or powdercoat needed before use
You must fully install BEFORE painting and then removed for paint or powder coating.
No cutting required on the frame rails on your Jeep JK
The two outside top bolt holes on your frame need to be drilled out to 9/16 inch
2012 and newer models will need a vacuum relocation pump bracket PN MB2060
Skid plate sold separately
LED fog lights sold separately
Specs:
Finish:
Bare
Location:
Front
Material:
Steel
Series:
Hammer
Sold As:
Each
Style:
Full Width
Thickness:
3/16 Inch
Vehicle Fitment:
2007 - 2010 Jeep Wrangler Wrangler
2007 - 2017 Jeep Wrangler Wrangler
2007 - 2017 Jeep Wrangler Wrangler
2007 - 2010 Jeep Wrangler Wrangler
2007 - 2017 Jeep Wrangler Wrangler
2007 - 2017 Jeep Wrangler Wrangler
2010 - 2017 Jeep Wrangler Wrangler
2010 - 2017 Jeep Wrangler Wrangler
2011 - 2011 Jeep Wrangler Wrangler
2011 - 2011 Jeep Wrangler Wrangler
2016 - 2016 Jeep Wrangler Wrangler
2016 - 2016 Jeep Wrangler Wrangler
2016 - 2016 Jeep Wrangler Wrangler
2016 - 2016 Jeep Wrangler Wrangler
2018 - 2018 Jeep Wrangler JK Wrangler JK
2018 - 2018 Jeep Wrangler JK Wrangler JK
2018 - 2018 Jeep Wrangler JK Wrangler JK
2018 - 2018 Jeep Wrangler JK Wrangler JK
2018 - 2018 Jeep Wrangler JK Wrangler JK
2018 - 2018 Jeep Wrangler JK Wrangler JK
